Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Blog Article
Everybody may have their unique piece of advice with regards to Installing A Bathtub.
Setting up a bathtub isn't specifically brain surgery, but it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old tub is conveniently easily accessible, the task can move immediately; if you need to open a wall to get rid of the old bathtub and position the brand-new bath tub, the task is a lot harder. In either situation, the job is within a house handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Ensure you have certified on your own for the work and also fit trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is much better to think about utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This post will assist you mount a new bath tub in your restroom if you have actually already purchased a new tub and do not need to change the setup of your previous water system pipes.
Your devices as well as product list should make up the following:
Planning for the Setup
To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the flexible tap adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of removing the existing taps can be rather troublesome as a result of the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. When the supply pipelines have been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, put the bathtub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bath tub up until the spirit level reads level.
To set up faucets, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; after that do the same for the other faucet.
Activate the water and also examine all joints and brand-new pipework for leaks and tighten them if essential. Fill up the tub as well as also examine the overflow outlet and the normal electrical outlet for leakages.
Finally, deal with the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has been used at the very least when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making certain that the washing machines are in place between the tap and also the sink. Secure the faucet in place with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former type must be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, triggering the water to pass through the wall surface between the bath and the tiling, leading to difficulties with dampness and also possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealer can fracture rather very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the floor tiles using waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am assuming you liked my article. Are you aware of someone else who is excited about the subject? Do not hesitate to promote it. Thank you so much for your time spent reading it.
Pro service, one dial away. Report this page